Guiguang GL01H (unnamed IC)
1-wire RGB · Guiguang Light · guiguang
- Channels
- RGB
- Bits / channel
- 8
- Supply
- 4.5–5.5 V
- PWM
- 1.5 kHz
- Backup data
- no
- Packages
- 3
The driver in Guiguang’s 5050, 3528 and 6028 “Fantasy colour” (幻彩) LEDs. None of the three sheets names the IC; “01H” appears only in the model number (GL5050RGB01H-T). The sheets are bilingual Chinese and English, dated May 2023, with a “copper bracket” (lead frame) noted for the 5050.
Datasheets disagree on the supply and threshold numbers between package sheets (see the refresh notes); the timing windows are identical across the 5050, 3528 and 6028 sheets. The GL5050 pin diagram numbers pins 1 to 4 on the drawing; the GL3528 drawing labels two pads “1” (a typo for 2 DOUT) while its table is correct.
Refresh & flicker
PWM 1.5 kHz, data rate 800 kHz, forwarding delay 0.16 us typical / 0.30 us maximum (page 5). The 5050 sheet gives a 4.5-5.5 V supply, 3.1 V / 1.5 V input thresholds and 0.45 “uA” quiescent (unit as printed, probably mA); the 3528 sheet gives 4-5.3 V, 2.6 / 1.6 V and 0.5 uA, and the 6028 sheets 3.5-5.5 V, 3.1 / 1.5 V and 0.45 uA. The recorded range is the 5050 sheet’s. The sheet says at least 1024 cascaded pixels at 30 frames per second and a scan frequency of at least 400 Hz.
Timing
| Source | T0H | T0L | T1H | T1L | Period | Rate | Reset | ± |
|---|---|---|---|---|---|---|---|---|
| datasheet ↗ | 300 ns | 900 ns | 600 ns | 600 ns | 1200 ns | 833 kHz | 180 µs | — |
| Min/typ/max table: T0H 250/300/350 ns, T0L 600/900/950 ns, T1H 550/600/650 ns, T1L 300/600/650 ns, reset at least 180 us. Programs must use a symbol period of at least 1.2 us and keep the low time of a 0 or 1 code under 20 us. 24 bits per LED, high bit first, in RGB order (the sheet says “sent in RGB order” - not the GRB order of most 5050 parts). | ||||||||
Clones & compatibility
“Compatible” is never stated bare here — each relationship carries how strong the claim is, and what bites if you assume too much.
-
electrically similar
SK6812
Inferred from the printed numbers only; no Guiguang sheet names SK6812 or any IC. The 2015 OPSCO SK6812 table (T0H 300, T0L 900, T1H 600, T1L 600 ns +/-150) sits inside all four GL01H windows, as does the 5050 pin order. But the GL sheets send RGB (SK6812: GRB), reset after 180 us (SK6812: 80 us in 2015, above 200 us in 2025) and a 4.5-5.5 V supply. A GRB controller will swap red and green. source ↗
-
electrically similar
Guiguang GL2121 (unnamed IC)
The GL2121 sheet prints a different timing table (T0H 250 typ / 300 max, T0L 1000 typ, T1H 620-1000, T1L 400 typ ns, reset 80 us) and a 3.5-5.5 V supply; see that protocol. source ↗
-
electrically similar of this
Guiguang GL2121 (unnamed IC)
Same maker, same RGB order and 800 kHz rate, but a different timing table from the 5050 / 3528 / 6028 sheets (T1H 850 against 600 ns typical, T0L 1000 against 900, reset 80 against 180 us) and a lower-voltage supply range.
Library support
Not checked against library source.
Parts using this protocol
Dating evidence
Evidence, not a release date. A library commit proves the part existed by that date and says nothing about how long before.
- 2023-05 datasheet revision Guiguang GL5050RGB01H-T specification, release date (发布日期) May 2023 on the cover ↗ month